It’s also the case when you first fill a swimming pool, and perfect water balance is no less important when first filling a pool than it is before you turnloose any kind of automatic pool equipment, automatic cleaners in the case of this post. In the opening 100 words of your pool-opening routine, you ought to be testing and adjustingfor the presence of chlorine, pH, alkalinity, calcium hardness, and stabilizer. Once the chemical treatment has taken place, tools like a skimmer, pool vacuum, and pool robotic pool cleaner step in to prevent debris and microscopic particles from getting in the way of your freshchemical levels.

Test and Add to pHand Total Alkalininty

1 – Fill your poolhalfway up the skimmer opening. Measure pH andtotal alkalinity with a good test kit. Try to achieve 7.2to 7.6, and the alkalinity between 80 120 ppm. If it is low, then you need to add pH increaser; if it is high, you will needto add pH decreaser. Correct alkalinity helps to preventpH fluctuations.

Clear with Chlorine orNon-Chlorine Shock

After pH is level, sanitizingis next. Be sure to mix anychlorine or non-chlorine shock according to instructions on the package. This first stage shock treats harmful bacteria, organic contaminants, and chloramines which are foundin fill water. Wait 46 hours, and then retest free chlorine; make sure it’s13 ppm.

Stabilize with Cyanuric Acid

UVlight breaks down chlorine quickly if your pool is outside. You can also add cyanuric acid (stabilizer) ata rate of 3050 ppm, which will prolong the life of your sanitizer in the sun. “Step one: Dissolve granules in a bucket of water and broadcast around deep end—never dump directlyover steps.

Adjust Calcium Hardness

Low hardness When hardness is less than 200 ppmit may be corrosive to plaster and liners. Scaling mayoccur at high hardness (more than 400 ppm). If hardness is too low, add calciumincreaser. Go ahead and use that and keep the level between200-400 ppm.

Prevent Algae with Algaecide

To help to avoid greenouts, even in hot, sunny areas,dose a base algaecide after your first chlorine shock. This layer makes your robot pool cleaner, pool vacuum robot work effectivelyIt can avoid filters prevents from clogging for long life.

Alt: robot pool cleaning checking andbalancing pool water with chemicals

Pre-Chemical andPost-Chemical Mechanical Cleaning

As the chemicals are circulating already, go do an initial debrisremoval:

Use a skimmer to collect leavesand surface debris.

Clean upheavy debris with a pool vacuum set to main drain.

After the chemicals have mixed (typically 24 hours), runyour robot pool cleaner or swimming pool robot cleaner through a full-cycle cleaning. Current models like the Beatbot AquaSense 2 Ultra, Beatbot AquaSense 2 Pro, and Beatbot AquaSense 2 are capable of filteringfine debris as well as some light algae, for sparkling clear water from the beginning.

For Tough Stains: AcidWash

If you see mineral rings ordeep stains around your pool tiles and around your steps, it may be the perfect time for a light acid wash using our guide on how to acid wash a pool for safe and effective removal of calcium build up. Always rinse thoroughlybefore returning to your robot pool cycle.

But What If YouCan’t Run Your Pump?

If you face a rare pump failure, you should have a good idea of how to drain an inground pool without a pump so that you can lower the water level safe enough to spot-treat and tile-clean without causingdamage to your equipment.

Enhance the Movement with aPool Booster Pump

For the water flow to go down on the shallow end of the pool or steps, keystoning a pool booster pump can allow chemicals to become emitted more evenly andyour robotic pool cleaner can travel easily to those hard-to-reach areas. Check out ourWhat is a pool booster pump primer for installation tips.

Not to Be Confusing: Can a RobotPool Cleaner Pick up Algae?

Typically your robot pool cleaner should easily pick up residual algae after you properly shock andtreat with algaecide. If you see green water, do what you can to suck up algae on your manual vacuum using the algae attachment, then run a stroke with yourpool vacuum robot.

Conclusion

Conclusion: If you are working with afreshly filled pool, start with the pH and Alkalinity, then an initial shock, followed by a Stabilizer, Calcium Hardness, and a preventative Algaecide. Clean out your leaf catcher, use your robotic pool cleaneror pool skimmer and pool vacuum before and after chemical movement. With a measured effortand the proper tools, your pool will remain crystal clear and swimmable all season long.

Information contained on this page is provided by an independent third-party content provider. XPRMedia and this Site make no warranties or representations in connection therewith. If you are affiliated with this page and would like it removed please contact pressreleases@xpr.media